IRRIGATION WORK - CHAPTER - 5

METHOD STATEMENT FOR IRRIGATION WORKS CHAPTER 5 l HOW TO DO IRRIGATION WORKS l IRRIGATION COMPANIES IN DUBAI

INSTALLATION OF CONTROLLERS

Irrigation controller will be installed in the location approved by the consultant and as shown on the approved irrigation shop drawing. Power supply for the controller will be taken from the nearest approved power source. All the cables from the solenoid valves will be connected to the controller.

TESTING AND COMMISIONING

The electrical equipment and complete system will be thoroughly inspected and tested before finally placing into service. All tests shall be made in compliance with respective regulations, recommendations and standards. As a minimum, check on mechanical function and pre-test of the functional sequence will be carried out in the workshop and visual inspection, insulation test (megger test), and check for functional sequences will be carried out at the site. In addition to this, any additional test as required will be carried out to the satisfaction of the consultant.

HARD & SOFT LANDSCAPE COMPY DUBAI

Irrigation controller will be programmed and cold tested for proper operation of the solenoid valves as per the programme. All the test documents will be submitted for the approval of the consultant.

Upon receiving the approval, pumps load test will be done to confirm the proper operation as per the pump curve. After this, the automatic portion of the irrigation system including electric control valves, quick coupling valves, sprinklers, spray heads and emitters will be activated in a fully automatic manner and run through a complete cycle. Station timings of the irrigation controller will be programmed as per the consultant’s instruction and each function will be demonstrated.    

EXCAVATION FOR TREES

Prior to start excavation for the pits, the location of the pits will be marked for approval of the consultant. Once the approval for the location is obtained, the individual pits will be excavated to the sizes specified. Excavated sub-soil will be removed from the site and will not be mixed with the planting medium. After this, the pits will be filled with irrigation water to ensure that the water will drain away. In case of poor drainage, a percolation test will be carried out. If necessary, drainage holes will be angered with the approval of the consultant.

PLANTING WORKS

         PLANTS / TREES

Once the planting pits are excavated, it will be backfilled with approved planting medium in layers. Overfilling will be done to allow for compaction/subsidence. During backfilling, slow-release fertilizer will be added as per specification. Tree stakes will be driven into pits prior to planting. At the time of planting, a hole will be made into the pit large enough to take the plants root ball. The planting hole will be thoroughly watered prior to planting. After this, plants will be carefully removed from the containers. Plastic pots will be split with knives and plants removed with all the soil intact around the roots. Extreme care will be taken not to damage the roots or the foliage of the plants. The plants will be placed upright so that the collar line (line of contact between soil and stem) is at the same level as the surrounding ground. Planting medium will be placed around the plant in the pit in layers, with each layer firmed separately to eliminate all air pockets until final soil level is reached. A circular watering basin slightly larger than the planting hole will be formed. Watering will be done thoroughly during and after planting. The area surrounding the plant will be restored to finished grade and excess soils and rubbish disposed of properly.

CHAPTER 1 l CHAPTER 2 l CHAPTER 3 l CHAPTER 4 l CHAPTER 6

SWIMMING POOL TILES SUPPLIERS IN DUBAI l LYING OF POOL TILES

SWIMMING POOL TILES SUPPLIERS IN SHARJAH l LYING OF POOL TILES

When you own a pool around your own premises you might discover that placing tiles can be just a significant advancement within a standard pool liner cloth in addition to strengthening its look. Infinite Leisure is the best Swimming Pool Tiles Supp.ilers in Dubai, You may create a charming pool surround by simply installing mosaic tiles using mosaic tiles to develop patterns that are creative. Additionally, it isn't important if you should be tiling only the partitions or even your full pool, however, be certain that you employ wrought pool tiles along with watertight grout to make sure you acquire appropriate, extended duration policy.

SWIMMING POOL TILES SUPPLIERS IN DUBAI

To begin with, empty your swimming pool the water amount is beneath your own setup lineup and also in a degree which you're glad to endure in. If you're tiling the full pool or your swimming or only do not need to stay in warm water at the same time you function, you also could empty all of the water altogether.

Wash out the top you're getting to put in your flooring using heated water along with typical dish soap and soap. This guarantees that all of the compounds, grime and other contaminants have been eliminated from your face area. Dry completely with a towel leave to get a couple hrs to wash obviously.

Now disperse cement glue over an area no greater than 4 5 square feet at one moment; point. It's possible for you to make use of a skillet towel that can abandon ridged from the glue therefore that the swimming pool tiles stay glued to it. Make certain you're using grout and tiles that are qualified for use in pools, rather than all services and products are ensured watertight.

Now push your swimming pool tiles right into place from the darkened location. The cause you to work in little areas is indeed the glue will not dry before you may place the pool tiles on it. Should you choose to wind up getting a few dry stains, then be certain that you scrape the old glue together with the advantage of one's trowel until you employ a brand new coating, or else you may find an uneven end. In the event you would like to continue to keep an exact optional border for your tiling, then temporarily screw up a wood plank in the base of just about every tile row to utilize as a director for hanging pool tiles in an identical degree.

In the event, you have to lower some tiles to get edges or even more compact areas to utilize a suitable tile cutter to reduce waste out of breakages. Bring a pencil on the rear part of the tile at which it requires glueing and after that slice line together with this filler. If you're employing thin tiles, it's possible to score the accord having a sharp knife and then after that just snap the tile together it.

Continue using glue and placing tiles before all is coated. Don't forget to do the job in tiny locations. Once you are finished and make everything for 48 hours accordingly that the plastic glue needs the time for you to wash entirely.

Simply employ your watertight grout into the joints between your pool tiles. Spread throughout the whole face by means of a grout float and then apply a bigger employ as a tsp deal with to compel the grout into the joints. Tend not to leave spaces or openings anywhere since this may definitely mean drinking water leakage when the swimming pool is emptied, that can wreck the total setup!

Wipe off all of the extra grout from the outside of these pool tiles utilizing a moist sponge. Let me dry for another 48 hrs and you may reinstall the pool and take pleasure in your amazing fresh swimming region.

To get a broad array of tiling and pool tiles tools and supplies, see http://www.wallsandfloors.co.uk for purchase prices and speedy shipping, offering free shipping and delivery of most tile samples arranged.